CDBCN Texas Instruments Logic Gates datasheet, inventory, & pricing. CDBCN datasheet, CDBCN circuit, CDBCN data sheet: FAIRCHILD – Quad 2-Input NAND Schmitt Trigger,alldatasheet, datasheet, Datasheet. CDBCN datasheet, CDBCN circuit, CDBCN data sheet: NSC – Quad 2-Input NAND Schmitt Trigger,alldatasheet, datasheet, Datasheet search.

Author: Voodootilar Tojakus
Country: Indonesia
Language: English (Spanish)
Genre: Education
Published (Last): 6 April 2005
Pages: 445
PDF File Size: 9.45 Mb
ePub File Size: 7.91 Mb
ISBN: 887-6-80149-359-4
Downloads: 46973
Price: Free* [*Free Regsitration Required]
Uploader: Tebar

Yes, you can use an LM, it will work dataheet as well in the above circuit, but put a 10K in cd4093bcn datasheet with the LED to keep the hysteresis about the same. The needs more supply voltage and the input common mode range does not include ground.

Questions Tags Users Badges Unanswered. I made a mistake and the trigger output is “sinking” the led instead of “sourcing” it, but the overall cd4093bcn datasheet is preserved: I have one around.

(PDF) CD4093BCN Datasheet download

This site uses cookies to deliver our cd4093bcn datasheet and to show you relevant ads and job listings. I dagasheet understand your inversion. This might work, what zener value you need I do not know, I would experiment a little. What am I doing wrong?

The Schmitt trigger ICs have rather poorly defined thresholds that are percentages of the supply voltage, not absolute voltages. I am trying to design a circuit using an intermitent power source cd4093bcn datasheet bicycle hub generatorwhich is rectified and filtered, and regulated at 6,8V.

Sign up using Facebook. I noticed you exchange the position between the Zener and its series resistor. Cd4093bcn datasheet R7 to have no hysteresis at all. You can try something like this, which uses half of an inexpensive cd4093bcn datasheet op-amp as a comparator. How could I properly activate the Schmitt trigger when the Zener is “on”?


It cd4093bcn datasheet be very useful to me, thanks! Is there a way to know if any other Cd4093bcn datasheet would work or not, or are there a set of characteristics that would guide me datasueet choose a fitting OpAmp for this application? If you could the Schmitt trigger’s input to ground then that stays constant as the trigger level changes cd4093bcn datasheet the supply. I made the zener voltage of D1 a bit lower, now the LED should switch on above 6. Spehro Pefhany cd40093bcn 4 A will not work.

This is clearly spelled out in the datasheet. If you derive the supply cd4093bcn datasheet the input voltage you have to take that into account. Thanks for your answer! The thresholds are around 6. Cd4093bcn datasheet trig buffer means the IC properly connected to power rails. Flip a Schmitt-Trigger when current flows through a Zener diode. Sign up using Email and Ccd4093bcn. Regarding the circuit with the Schmitt trigger, note that the levels of the Schmitt trigger are relative to the supply voltage so it is chasing a moving target the trigger level moves up as the supply goes dafasheet.

Sign up or cd4093bcn datasheet in Sign up using Google. Make R7 daatasheet to increase the distance between the trigger levels. Also, do I assume correctly that altering the proportion beetween R6 and R5 I could tune the values of the input voltage thresholds? The circuit presented in electronics.


CDBCNInternet thinking Electronics Co., Electronic data resources trading network

Could you elaborate on that? If the input voltage is Vcc – 6. By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your cd4093bcn datasheet use of the website is subject to these cd4093bcn datasheet.

The LM is likely the cheapest op-amp cd4093bcn datasheet the world maybe a penny or two in volume and is suited for this application, especially the wide supply range. It is not what you need. By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service.

Humpawumpa I added the schematic. It’s the dual version of the quad Cd4093bn that Bimpelrekkie used. Pardon my lack dagasheet knowledge, but could cd4093bcn datasheet please tell me why the doesn’t work? Could you provide a schematic of the schmitt trigger variant as well? In my 2nd circuit the zener makes a reference voltage, let’s cd4093bcn datasheet it is 3 V.

Change R4 to alter the hysteresis. Post as a guest Name.

R7 is optional it adds a bit of hysteresis like in the Schmitt triggers.